M38 – M38A1 Jeep Parts

Blackout Driving Light Guard

Now Available a new high quality black out drive guard.  This is not the guard that has previously available.  It is an entirely new product.

Special Price $35.00

M38-M38A1 24V B.O. Drive Light.

This is the light that mounts on the
left front fender N.O.S.
$85.00

M38A1 Springs

U.S. Made M38A1 Springs Front and Rear

Now Available

$150.00 each

*Note - the new springs are not actually pictured above.

.

.

.

Body Step

These are the new high quality U.S. Made Body Steps.  These are not like the garbage that has been available in the past.  Pictured are the M38 type which are the same for the same for  MB, CJ2A and CJ3A.

$40.00 each

Now Available Semi-Gloss 24087 by Randolph Products.

This is a real Mil Spec paint.  Highest Quality available.

Introductory Price - $33.00 per Gallon*

Aerosol Sprays - $6.00 each

*Hazmat Charges apply on Gallons

M38 Reference Guide

For years there has been very little information available on the M38 Jeep.  We are now proud to offer a must own book for any M38 owner.  This book has been in development for the last five years and will answer a lot of the questions that most restorers have on the M38.  It covers the differences in parts and accessories.

Price $60.00

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)

M38A1 Emergency Brake Shoe Set

This is a set of the New U.S. Made Emergency Brake shoes.  These are not like any other shoes that have been available.  There have been poor copies of this piece available for years, but we have copied an original sample.

Price $75.00

Also Available All other attaching parts for the emergency brake system.  Call in what you need.

M38/M38A1/M37 Timing Adapter

This is a very useful tool.  It is used to go between the spark plug and the ignition wire so that you may attach a timing light for checking the timing.  This is U.S. Made.

Price $45.00

M38-M38A1 Seat Pan Driver & Passenger

This is a high quality reproduction of the seat pan with weld nuts.

$40.00 each

1/4 Ton Trailer Lunette Eye

This is the new drop-forged, heat treated and plated U.S. made 1/4 ton trailer Lunette Eye.

$185.00

Spring Available at $17.00 // Nut Available at $1.00

M38 Front Floor Pan

These are the new high quality replacement floor pans.  If your front floor pans are rotted out these replacement pans are the solution to your problem.  They come with all holes drilled and weld nuts in place.  Sold individually as left and right side.

Price $95.00 each 

(click for larger picture)

Hat Channel Kit also available for $145.00

M38A1 Front Floor Pan

These are the new high quality replacement floor pans.  If your front floor pans are rotted out these replacement pans are the solution to your problem.  They come with all holes drilled and weld nuts in place.  Sold individually as left and right side.

Price $135.00 each

Hat Channel Kit also available for $150.00

M38 Cowl/Dash Support

These are a new high quality product which will also fit MB, GPW, CJ2A & CJ3A.  Left and Right side available.

$35.00 each

M38A1 Fuel Tank Well.  This is a high quality U.S. made reproduction.  This part is always rusted out and generally not salvageable.  $125.00

M38 Air Cleaner Tube

This is an exact reproduction of the air cleaner tube for the M38.

$70.00

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)

M38 Air Tube Hose

This is an exact reproduction of the hose for the air tube shown here with clamps.

Hose $20.00 / Clamps $3.50 each

Grill Marker Light Assembly

This is the light that is mounted in the grill. They are the real deal, original NOS with metal connector. 

Price $75.00 ea.

M38-M38A1 grill marker light cover.
These covers are always painted over
or missing their lens. Replace them
now for only 

$20.00 each.

Headlight Assembly

This is a complete 24 Volt Headlight Assembly with bulb, housing and trim ring.  This is an original NOS piece.  

Price $115.00

24 Volt Headlight

These are Wagner U.S. made with correct Douglas connector.  Price $32.00

Also available with rubber Packard connections.
Price $30.00 

M38 Headlight Guard 

This is the guard that protects the headlight. I had these made out of frustration of not being able to get a good quality guard. These are the best available. I guarantee it. 

Price $15.00 each

 M38-M38A1 Headlight Dimmer Switch with Metal Connections.  Also fits M37.

Price $45.00

Complete wiring harness kit, these are the
 best kits available. They all come numbered 
with metal shells and wiring diagram and are setup for turn signals at no extra charge to you.  This is an option others charge extra for.

Price $535.00

24 Volt Distributor New

These are NOS complete with coil - Price on Request. 

Also Available - Rebuilt - Price on Request

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)

M38-M38A1 Master disconnect switch.
This switch was not stock on the M38-M38A1 but can be retrofitted to fit any place,
helps eliminate dead batteries.
$30.00 

Please scroll down to view more items.

.

.

.

.

Amp gauge. For years I have struggled with
where to find amp gauges, and now I have a solution, this is a surplus A.C. gauge but it has
conventional type connectors on the back of it.
So I made an adapter for them so you can connect your Douglas connector to it. From 
the front of the dash you can not tell the difference. $50.00  

Slave cable bracket exact copy of the original for M-38 $15.00 Slave cable $65.00 N.O.S.

NOS Start Pedal M38/M38A1

This is the pedal that is mounted to the floor board which pushes the starter.

$20.00

Rubber Pad is also available at $5.00

Speedometer cable, these are the original
water proof speedometer cable
for M38-M38A1 N.O.S.
$75.00

We also have a replacement cable available for $45.00. (not pictured)

Battery Box Cowl

This is a high quality reproduction of the Cowl Battery Box.

Box with Bottom $110.00

Bottom separate $34.00

Battery Box Under Hood

This is a high quality reproduction of the Under Hood Battery Box.  This comes complete with bottom tray, battery hold down with bolts, fender mount brackets and decal.  You will find no better box than this one.

Price $235.00

Now Available!

M38-M38A1 Battery Tray

This is an exact reproduction of both M38 and M38A1 Battery Trays.

$70.00 ea.

Battery Cable Set available for M38 and M38A1.  These are an exact reproduction with the correct military spec cable.  $70.00

Cable Ends available at $5.50 each

Battery Box Bottom M38A1

This is a part that is always rusted out.

Price $39.00

M38A1 Battery box cover, this is another high
quality reproduction from an original die.
$85.00

Screws now Available $3.50 each

Also Available Late type with Strap

M38 Emergency Brake Cable

Never before available - This is an exact reproduction with wire wrap.  Comes complete with two clips and correct handle. $100.00

-----

Also available from a different supplier cable available no handle and no clips $75.00

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)

M38/M38A1 Brake Tube and Bracket 

This is a combination of reproduction brake tube and NOS frame bracket.  Replacing these parts will take out the play in your clutch and brake pedals.  

$75.00 for tube and bracket, Also sold separately

Clutch and brake pedal set. Replace those worn out pedals with a set of N.O.S. 

$35.00 each

M38 and M38A1 brake line set, this is the complete steel line set with clamps, copied from original lines and U.S. made.  I also stock brake and fuel line sets for all models. Call me.. 

$95.00

Master cylinder heat shield, this shield is
always missing, helps keep brake fluid
from boiling, exact repro.
$40.00

Fuel tank neck grommet. I had these made by
 the original government contractor, these
 are not cheap imports like those that others sell.
$18.00

Data Plate Set M38 & M38A1

These are sold as a complete set.  Mounting plate sold separately.  These are the highest quality data plates available today.

$48.00

Data Plate Mounting Plate 

I had this made from an original plate. Drilled and ready for data plates. $15.00, data plate set available $48.00 rivet set $3.00

M38 Fuel Primer Kit

This is a NOS fuel primer kit for the M38 and M38A1.  $75.00

Carburetor rebuild kit. This master carb kit
is the best available, not the junk kits that 
others sell. $55.00 Two for $95.00

M38 Master Bow Bracket Set

These are all the parts to install your bows.  These are high quality U.S. made reproductions.

$112.00

Also available individually, Call me.

M38A1 Master Bow Bracket Set

These are all the parts to install your bows.  These are high quality U.S. made reproductions.

$112.00

Also available individually, Call me.

M38 - M38A1 Rear Crossmember

 This repro is likeno other, copied from an original with correct inside support, pintle hook plate & rivets.

Price $115.00

Top Bow Rod Set 

These are the rods that go between the bows and the windshield frame.  This is U.S. made .

$42.00 for a full set

M38 - M38A1 Front Bumper

New High Quality copied from an original with tapered ends.  This is the best bumper available today.  I offer it in two sizes, standard and long.

Price $85.00

M38A1 Hood Bumper

These are the bumpers mounted on the top of the windshield frame.

$25.00 per pair

M38-M38A1 Front lifting shackle, this is
an item that is always missing, I had it
reproduced from an original. $17.00
I also have the bracket, pin & clip.

M38-M38A1 Rear lifting shackle,
these are N.O.S.  $17.00
I also have the bracket, pin & clip.

M38A1 Spare Tire Carrier

If you've purchased a spare tire carrier elsewhere and the mounting holes do not line up you will never have this problem with this product.  This is a U.S. made exact reproduction and even comes with the mounting hardware and spacers.

Price $125.00

M38/M38A1 Mirror Arm

This is a high quality double jointed mirror arm made in USA.

Price $32.00

High Quality Tinted Mirror also available at $20.00

NOS Axle Bumpers M38/M38A1

These are original Axle Bumpers for the M38 and M38A1.

$12.50 each

Tool box seal. This is the seal that fits around
the tool box door  I had this one copied 
from the original.
$15.00

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)

The Long Awaited Green Sheller Steering Wheel is Here.

This steering has never before been available in true green plastic.   For years the best you could get was a steering wheel that was painted green which eventually would wear off.

This wheel is truly an excellent reproduction of the green Sheller steering wheel.  It has the grooves embossed in it like the original and the Sheller name stamp.

This steering wheel is correct for all M38 and M38A1 and also early MB and GPW.

Price $160.00

Green Painted Steering Wheel 

This steering wheel is good for the less discriminating Jeep owner. Fits either M38 or M38A1.

Price $95.00

Steering column floor seal and plate for
M38-M38A1, CJ2A-3A, 3B.
$15.00 Set.

16' Wheel

This is a replacement wheel. 

$98.00

Rifle Bracket Set M-38

 These are the brackets that hold the rifle carrier to the windshield frame.

 3 Piece Bracket Set $25.00 

Rifle Rack also available for $155.00

Rifle rack

 This was mounted on the windshield frame of M38 models. It is the best reproduction of  this item available.

Price $175.00

M38A1 Windshield to Cowl Rubber

This is the highest quality cowl rubber available for the M38A1 unlike others being offered that are too thick and don't fit properly.

Price $40.00

M38A1 inner windshield rubber this is the rubber
seal for the two piece windshield. A perfect
reproduction, complete with lock strip. 
$80.00 

M38 Cowl Rubber

We are pretty excited about this new product.  This is an exact reproduction of the M38 cowl rubber which has been in production for over a year and copied from an original sample.  You may not be aware of this, but cowl rubbers vary from model to model and the M38 rubber is different from all the rest.  If you are looking for that perfect fit, this is the one to buy.

Price $49.00

Correct Screws available $3.00 per set. 

M38 camshaft, this N.O.S. camshaft comes in  original package dated 50's, buy it now while
They still exist. They will fit all L head engines 
with gear CJ-2A/3A $75.00

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)

M38-M38A1 engine stay cable, this cable
 mounts between the bell housing and transmission cross member N.O.S.
$18.00

PCV valve, this valve is always clogged
or missing. Fits both M38-M38A1 
and MB-GPW.
$35.00

M38 Crankshaft Pulley

This is a high quality replacement crankshaft pulley made of solid steel.  Because of its construction, there will never be a problem of separation of pulley from hub.

Price $125.00

Engine Motor Mounts M38-M38A1

These are the new High Quality motor mounts now available for both the M38 and M38A1 with correct reinforcing plates.  In the picture above M38A1 shown on left, M38 on right.

$17.00 each

M38A1 Clutch Cable

This is a new reproduction for the special clutch cable for the M38A1.

$15.00

Clutch boot with fitting. This is the fitting that screws into the bell housing to hold the boot.
 This boot helps keep dirt and water 
from entering the bell housing.
$35.00 as a set or $17.00 boot and 
$22.00 fitting.

M38 ignition filter w/ cable. This is the firewall mounted filter used on the early model M38,
it comes with cable and it is N.O.S $65.00

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)

Transmission and Transfer Case Shift Lever Boots

Transmission Boot $15.00

The Transfer Boot is new and improved with a high quality material that will resist sun damage.

Transfer Case Boot $12.00

Decal set these are all the decals used under the hood and dash, they are sold in double sets, just in case you make a mistake when installing them $16.00

Please scroll down to view more items.

M38 radiator seal set. These are the seals that
go around the grill to deflect the air to 
radiator, a nice reproduction w/ staples.
$20.00 

M38/M38A1 Inside Mirror w/ Mounting Bracket

 Price $25.00

(please also visit our M38-M38A1 Catalogs to see our full selection of Jeep Parts)